Showing posts with label sdr. Show all posts
Showing posts with label sdr. Show all posts

Monday, 6 August 2018

Moving Pictures! First dabbles in Amateur TV

I am always keen to try something new and I've spent the last couple of weeks experimenting with some Amateur Television ATV and Digital ATV (warning this post is bit of ramble and information overload)

They say "a picture paints a thousand words"and I've always liked the idea of sending pictures via radio having dabbled with sending and receiving SSTV and SSDV, including pictures from High Altitude Balloons (HABs) like the Hamfest HAB flight I did back in 2015


But I've also been intrigued by "Fast scan TV" to transmit moving images. I've seen demonstrations at conferences and in online videos and joined the British Amateur Television Club BATC a few years ago but apart from reading the CQ-TV magazine I had not done anything mainly due to expense and investment I mistakenly thought I would need to make.

Recently I have seen mention of using easy and low cost equipment to get on the air on 5.6GHz (the 6 cm amateur band) using cheap modules intended to transmit “First Person Video” (FPV) back from drones.
 
These simple units can be used without any modifications to get on air. A number of operators have used them with high gain WiFi panel and/or dish antennas with a clear line of sight path to send pictures to stations using the same equipment over paths in excess of 50km, the current record is over 160km. Chris Leviston M0KPW has an excellent website describing his 5.6GHz system http://www.5-6ghz-atv.co.uk/ and there is more information at the BATC Wiki https://wiki.batc.org.uk/5.6_GHz

Inspired I ordered some kit from eBay a few weeks back, a receiver module and transmitter arrived quite quickly (no slow boat from China this time)


The equipment is powered by a 12V supply and input and output is a composite video signal and audio. It can be fed by a standard camera or video source but I dug out an old Raspberry Pi and soon had it generating and transmitting a test card with the required call sign overlay. The modules are channelised, the displayed 33 number is bank 3, channel 3 which is 5.665GHz selected by the BATC since it sits inside the amateur allocation,


Over the week I refined the Pi software, adding the Pi camera and various libraries in python to generate video with informational overlay, adding a GPS allowed calculation of the locator square when out portable. I have put it in a box (sorry no picture of that) and a switch to flip between live video and test card. I also had a bash at making some double biquad antennas. Regularly updating my twitter feed with various milestones (I recommend you follow me)

While browsing the BATC website for information I spotted that there was an ATV Academy workshop being organised by the Telford and District ARS, giving people the opportunity of finding out a bit more about ATV and people could bring along their equipment and projects for advice. So at the last minute I decided to go but because of the distance could only really go on the Saturday. But it was well worth it and a great day. I was made to feel welcome by everyone there and was able to show off my modest achievements on 5.6GHz and learned about the BATC Portsdown Transceiver and MiniTioune receiver projects, even buying the parts to build the receiver.

The academy coincided with a BATC Activity weekend and they were going up to the summit of the nearby Long Mynd to operate on the Sunday. Since I wasn't there I had planned to go to a local high point to see if I could make contact with some of the other operators and stations and got the kit ready on a cheap lighting tripod. I was going to use an old portable satellite dish with one of my double biquads at the feed point.

The satellite dish is inverted because they are offset so when the dish is vertical they are actually pointing around 20 degrees upward towards the TV satellite (in the UK). So for terrestrial use with low elevation they work better inverted. (see here for better description of offset dishes)

I did venture out but I chickened out setting up due to a combination of a surprisingly busy road, fly tipping and very hot conditions. Due to the the fly tipping in the lay-by I didn't want to be seen getting stuff out of car boot! especially as a few cars had slowed down as they passed.

Nevermind I have ordered couple of cheap high-gain mesh dish antennas so when they arrive I will get out again and arrange some skeds, hopefully roping in some of the radio club.

In addition to the 5.6GHz stuff I have also taken possession of an ADALM-PLUTO SDR from Analog Devices. It is inexpensive (£90/$100) and designed to allow educational experimenting in software defined radio. It is a SDR receiver and low-power transmitter. They had been in short supply but availability has improved.

Charles Brain G4GUO has added support for the device into the DATV Express software. I am hoping to use it for some experiments in RB-TV (Reduced bandwidth TV) so I can actually use my NoVs

I took the PLUTO along to the ATV workshop and was able to see it transmitting and being received by other peoples receivers. So last night I got out the two satellite receivers I have and with a little bit of persuasion with settings got some DVB-S DATV transmitted and received.
Anyway, that is enough for now.. but will try to keep the blog updated as I experiment some more, but follow my twitter account @nerdsville for realtime updates 73 Andrew

Wednesday, 29 May 2013

The joys of RTL-SDR and Taxi MDT Decoding

I have owned and used radio scanners for many years, and loved them as my posts before December 2011 will testify.

In that month I became the proud possessor of a FUNCube Dongle Plus and discovered the joys of software defined radio, since then I purchased a FUNCube Dongle Pro+ and extended my SDR adventures in to the realms of HF and I have several of the insanely cheap RTL2832 based dongles.

As much as loved my scanners there was a major flaw with them, which has been brought into sharp focus now that I have used SDR.

No matter how fast or as sensitive as the scanner is are you are still playing a game of chance. You are limited by the frequency steps, demodulation modes and scanning rate of the receiver and you could zip through the band all day and still miss those elusive signals.

SDR and the waterfall display is a revolution, you can view a portion of the spectrum in real time and actually see the signals, they may be short lived bursts of data and voice, or continuous data transmissions.

The RTL-SDR dongles excel in this respect with their wide sampling rate you can view up to 2MHz of the spectrum at once, the following images show typical waterfalls captured this morning using one of my RTL-SDR dongles.


The first one, shows the cluster of data channels (was the old Vodaphone Paknet system) around 164.2 - 164.4 MHz, a trunking control channel and various data bursts, which are mostly Taxi Mobile Data Terminal (MDT) transmissions.


A little lower down the spectrum and another trunking control channel, a speech conversation, more data bursts and a faint digital channel.


Further up the spectrum into the UHF, a cluster of data transmissions.

Simply moving the cursor on the display and you can hear the transmission, if necessary change the demodulation type, widen or narrow the filter bandwidth, save the frequency. If you capture the IQ file you can then replay it endlessly tweaking and refining until you extract the information you want.

During the weekend I was experimenting and noticed there was lots of data bursts in the 163-168MHz range, I confess that I already knew what most of them were as I have experimented before with a scanner (with a discriminator tap) and Ian Wraith's Java based Taxi MDT decoder. I decided to reinvestigate them using the RTL-SDR as the receiver.

While many taxi companies still use voice transmissions, many have adopted automated data terminal systems, where the dispatcher sends information about jobs to terminals in the cars, the drivers then can accept jobs, get information and send information back to the dispatcher.

Ian's decoder which requires the Java runtime environment decodes systems that use the same physical layer as MPT1327 i.e 1200 Hz and 1800 Hz tones transmitted at 1200 bps. The two main systems used in the UK, are the Autocab and Auriga. The Taxi MDT Decoder currenly decodes the Autocab, but the coding for the Auriga system is still an unknown, so just outputs the raw data.

More information about Taxi MDT Decoder can be found here I confess to having one slight niggle with it, often I couldn't get it to accept sound from the selected input. A work around I found was to first open the Audacity sound editor which I had installed and select the input and start a recording, then opening the decoder seems to make it work!

Ian has also written the excellent DMRDecoder which allows analysis of the DMR digital mode which is becoming more widespread. I intend to post some details soon about decoding digital modes, keep watching.

I created a video showing the Taxi MDT Decoder in action, the quality is pretty dire but you can get the idea, I identify the Auriga as being encrypted, it might be but as nobody on the team knows the protocol yet!

Tuesday, 23 October 2012

FUNCube Dongle PRO+ in production!

Howard is busy assembling and shipping out the first units of the FUNCube Dongle Pro+



I registered my interest early on and am one of the few to have got a confirmation email.
Thank you very much for your interest in the FUNcube Dongle Pro+ that you made on 28 September 2012. This is confirmation that your request is on our waiting list and we will be notifying you by email when we have stock.
I apologise for any delay in receiving this confirmation: the ecommerce software were using doesnt seem to automatically send out responses, so far Ive had to come up with a semi-manual alternative. As I write, there are already a total of 1,233 unique emails on the waiting list, so it may take a few weeks to satisfy the demand.

This was the confirmation for my second attempt at registration, so probably missed out of getting one early. Not sure if it means I am 1233rd or one of the 1233... time will tell, but certainly am very eager to get my hands on one.

At the moment the new PRO+ version won't work with SDR-Radio my SDR software of choice, but integration is apparently being worked on as we speak. But it seems it is supported by SDR# which I have briefly used.
I am very eager to see the filtering and performance improvements and being able to use on the HF bands, mind you tempted to get another of the RTL based receivers this time with a new tuner following the demise of the E4000. Apparently they work from around 25MHz and are much more sensitive.

Tuesday, 25 September 2012

FUNcube Dongle PRO+

Ever since I got my FUNCube Dongle Pro last Christmas it has been the main focus of my radio experimentation. I have used it on a number of computers including some quite old not very powerful machines and with different software applications primarily the SDR-Radio and HDSDR suites.

It was a little fiddly to initially set up but I have been impressed with its performance, it has opened my eyes and ears to what is out there on VHF and UHF, much more than I could ever monitor using my scanner receivers. Have a look at my previous postings.

Being SDR, with all decoding being done in software, it is effectively capable of all modes capable with the added advantage of having a variable bandwidth which is useful for data modes.

I have decoded images broadcast from orbit, received transmissions relayed via satellite and even bounced off the surface of the moon! As well as listening to all manner of terrestrial broadcasts.

In a word it is BRILLIANT.

It has its faults, or should I say limitations. It would be nice to have more of the spectrum available at one time and the front end filtering and rejection is troublesome at times. However this is more than made up for by its versatility and performance and it often out preforms my PRO2006 on the same antenna.

On the various forums and social networks it irks me to see people complaining about its performance but then they are usually the same people who go out and purchase a sub £20 RTL2832U based USB FM/DAB/DTV receiver dongle from eBay to use as a SDR and then complain they cannot get it to work or that its performance is lacking. But then that seems to quite common at the moment, everyone expects to just plug it in and it to just work with the minimum of understanding, involvement or experimentation but I digress.

Unfortunately Elonics the suppliers of the tuner chip in the FUNCube Dongle PRO are currently in liquidation and so they have struggled to produce any more units since July this year. This has potentially serious implications for the whole FUNCube educational project as there is no earth based component. Therefore the FUNCube team have instigated a redesign of the receiver and in doing so have increased its functionality and addressed some of the issues. This is the FUNCube Dongle PRO+

 
The new FUNcube Dongle Pro+ offers the following features and enhancements:
  • Full coverage of all amateur bands from 136kHz through HF, 6m, 2m, 4m, 2m, 1.25m, 70cm, 33cm, 23cm (150kHz-240MHz and 420MHz-1.9GHz, 70kHz-150kHz coverage through your software’s NCO offset)
  • 0.5ppm TCXO
  • 192kHz sampling rate
  • Eleven discrete front end filters
  • Super sharp SAW filters on 2m and 70cm
It is expected mid October 2012 and you can register your interest here

The official release of the FUNcube Dongle PRO+ was made during a presentation given to the AMSAT-UKInternational Space Colloquium 2012 on Saturday September 15. You can view the presentation by following these steps:

- Go to http://www.batc.tv/
- Click on "Film Archive"
- Select "AMSAT 2012" in Category box and click on Select Category
- Select "02 - FUNcube PRO-PLUS" in Stream box and click on Select Stream

Or download the whole video of the presentation from
http://www.batc.tv/vod/AMSAT%20session2.flv

Sunday, 15 July 2012

Experiments with an SDR4+ and a scanner refurb

Seems the holiday in early June broke the blogging momentum and unfortunately work commitments since and the stresses involved as a major project nears deployment have sapped my time and energy, so not had much to post.

Family commitments too have also eaten into my spare time not leaving me time or inclination to experiment. The FUNCube Dongle and the Ultra-cheap RTL-SDR have been unplugged for several weeks and I am ashamed to say most of my evenings have been sent slumped in front of the TV often nodding off to sleep rather than tinkering away.

That is not to say I have been completely idle! I have spent the last couple of weeks with a Cross Country Wireless SDR4+ receiver courtesy of my younger brother. For a while I have toyed with purchasing one after seeing them at last years Hamfest and have read some decent reviews. The SDR4+ is a HF Software Defined Radio covering 0.85 - 30MHz, the full specifications can be found on their website.


My brother shares a similar interest in radio, probably as he was forced to share a room with me when we were younger and I would subject him to listening to all sorts of strange signals late into the night! Well he decided to purchase one several weeks ago, but was frustrated when it didn't seem to work. On one of visits to see my Mother I took a cursory look and couldn't make it work either. To cut a long story short while he went away on holiday I borrowed the unit away to see if I could figure it out.

Following some experimentation and discussions with Chris Moulding on the Cross Country Wireless Yahoo Group turned out the problem was some dodgy USB ports and/or USB leads! The thread can be read at http://uk.groups.yahoo.com/group/cross_country_wireless/message/2136

I strung up a long random-length wire antenna in the loft and have managed to get some decent results on some bands, but interestingly very little on others, probably due to the lack of an ATU. But I have received lots of broadcast AM, some DRM (but not actually decoded) and buckets loads of Amateur transmissions, LSB/USB voice and Morse, RTTY and PSK31 from Europe, and decoded some HF-FAX. Sadly the SDR4+ will soon be off back to it's rightful owner, but has certainly wetted my appetite.

I have also refurbished my Realistic PRO2022 scanner, as I posted back in 2010 this was my very first scanner and sadly was looking a little bit worse for years of wear. It is still functional, especially for listening to airband but the displays electro-luminescence back light had faded and it was looking a little grubby.



I had already replaced the backlight on my PRO2006, but this was a lot easier due to the display being easily accessible with the simple removal of the front panel, and the EL panel being on flying leads rather than soldered on to a PCB. 



I found a cheap supplier of a suitable EL panel on Ebay and quickly had the new one cut to size and fitted, giving a lovely new blue display.


 The next thing was to clean the grime and grease that was encrusted on the case and knobs, using a small amount of Clit-Bang degreaser and being very careful soon had the case looking almost as good as new!


Tuesday, 22 May 2012

RTLSDR - Part 4 - Cutting out the noise using a simple coax filter

One major limitation of both the FUNCube Dongle and the RTL-SDR based receivers is the poor front end filtering.

Connecting a wide band antenna such as a discone to the input often results in a spectrum full of noise which swamps the target signal.

In most cases the noise is actually a result of out of band high-power transmissions such as FM and TV broadcast stations and pagers which overload the receiver and get mixed in to the tuned signal. The effects can be mitigated to a degree by turning down the gain of the receiver but at the expense of sensitivity to the signal you are wanting to receive.

The FUNCube Dongle in my experience seems especially susceptible to the effects of FM broadcast signals when trying to monitor the 2-Meter amateur band. I'm not sure if the current weather conditions were the cause but yesterday evening it seemed the breakthrough was especially bad. So I decided to experiment with a simple coax 'notch' filter.

There are two approaches to filtering, one is to use a band-pass filter which passes frequencies within a certain range and rejects (attenuates) frequencies outside that range. The other is to use a band-stop filter that passes most frequencies unaltered, but attenuates those in a specific range to very low levels. A notch filter is a band-stop filter with a narrow stop band.

As it happens you can make an effective filter using ordinary coaxial cable which will generate a sharp, deep notch which can be used to attenuate the unwanted signal.

A coax stub notch filter can be made if you connect the antenna to the receiver using a T-connector then attach a piece of coax of the appropriate length (the stub) to the remaining connector.

I happen to have a fair bit of 10Base2 Thin-Ethernet cabling (RG-58U) and connectors which were repatriated from a previous employer over a decade ago. The network cards they used came supplied with lovely long high quality 10m patch leads with moulded BNC connectors and a T-Connector and terminator! Even back then the 10Base2 was completely redundant as the network infrastructure used Cat-5 cabling.

So I dug out one of the T-Connectors and a BNC connector and set to work, connecting the antenna and receiver was simple, all I needed was to construct the coax stub.

To calculate the length of the stub you must first calculate the wave length of the desired 'notch frequency' for the FM band a good central notch frequency is around 100MHz.

The wave length is found by dividing the speed of light (which is around 300,000km/sec in free space) by frequency

So for a 100MHz signal the wave length is 300/100 = 3 meters.

However the speed of the radio wave in a coax is affected by the material it is made of, this is called the velocity factor. For most solid polyethylene coax (e.g RG-58) this is 66% (a handy table can be found here)

So multiplying 3 x 0.66 = 1.98 meters

The coax stub is 1/4 of this wavelength = 1.98 x 0.25 = 0.495 (49.5 cm)

So cutting a piece of coax of that length, connecting it to the T-Connector and leaving the other end open completes the filter. The filter will have maximum attenuation at 100MHz (assuming the coax is cut accurately) and the attenuation will fall off away from this 'notch frequency' (Note the filter will also notch at 300MHz, 500MHz and so on)

Interestingly it seems my RTL based SDR receiver is more affected by pager breakthrough, so I plan to make an alternative stub, adjusting the calculation to use 153MHz as the notch frequency to reduce this. It is possible to add more than one filter at a time using multiple T-Connectors and alternative higher performance designs for coax notch and band-pass filters can be found with a quick Google search.

I made a quick video showing the effectiveness of this simple filter which took about 10 minutes to make!

Monday, 21 May 2012

Some audio from the 144MHz SSB Contest

Not had much radio time since Saturday due to family duties but did managed to find time to edit down some of the audio from the 144MHz SSB Amateur Radio Contest I received.

The first part of the audio was from the FUNCube Dongle, the latter part from the Ultra cheap NewSky DVB-T stick running the RTL-SDR driver.

Both were received using the loft mounted discone antenna which I believe is vertically polarised and so wasn't optimal since SSB is broadcast using horizontal polarization. Even so I was quite impressed with what I did receive with such humble equipment.The stations calling in the audio were G0VHF (morse and voice), M0KWP, M0BAA, 2E0KWM and G4SIV

  144MHZ SSB Contest by nerdsville

Please note the corruption that can be heard toward the end of audio appears to be an artifact of the sound editor and/or the transcoding used by soundcloud as it wasn't in the original audio.

Sunday, 20 May 2012

RTLSDR - Part 3 - CQ CQ Contest

As it's the weekend I have managed to experiment with my new SDR device. I have sorted out an adapter so I can connect it to the loft discone and it has been pulling in some very nice clear signals. I have had to do some tweaking especially of the usb transfer buffer size to get some decent audio out of it. I have also had to learn how to use the HDSDR program which I haven't used much before favouring the SDR-Radio one with the FUNCube Dongle.

One thing that caught me out is that when I last used HDSDR with the FUNCube I had to swap the I and Q signals and I don't need to with the Newsky Tv28t so initially I was very confused as it all seem arse about face! Duh! But now actually growing to quite like it as having a much wider spectrum to see is very nice.

By a pleasant coincidence yesterday saw the start of the RSGB 144MHz May Contest so lots of SSB transmissions to tune in to. The FUNCube definitely has the edge when it comes to quality of audio and sensitivity and being able to tune down the gain helps in preventing out of band signal overloading the front end. With the Newsky device I've had to have the gain right up most of the time, but I suspect there is still more optimising to do.

Just a small video showing some of the SSB Contest signals on the spectrum. Don't you just love the masses of noise? Really must do something about that damn router!


I've also got to discover how to calibrate the Newsky as it shows quite a bit off frequency, I understand I need to discover the actual crystal clock frequency and can feed that into the EXT-IO plugin.

Friday, 18 May 2012

RTLSDR - Part 2 - Hello.. Hello Can You Hear Me?

As suspected the problem was indeed the computer. I rushed home at lunchtime and in less than 10 minutes I had installed the software on my main PC and it sprang to life just like the video promised.




I only had a short time to try it out, but picked up some FM stations, pager signals and the RAF Waddington ATIS which should have been on 291.675MHz but the frequency on the HDSDR screen was way off.

It does appear to be a little deaf but I hadn't got a decent antenna connected so I won't conclusively say that yet as I've got to make up an adapter this evening so I can connect the loft antenna on. Also the EXT-IO interface has a gain control that I didn't alter from the default.


RTLSDR - Part 1 - Failed to Launch!

 

Well that was quick! The USB Receiver with the RTL2832 receiver I ordered it on Tuesday afternoon and arrived yesterday (Thursday) morning (from Jersey based retailer Cosycave via ebay) so was eager to try it out last night.

Fired up the old laptop and went off to http://www.rtlsdr.com/ and the getting started section to download the drivers and software and everything seemed to be going well. Following the instructions the device appeared to be correctly detected and the appropriate drivers installed, but then it went pear shaped.

HDSDR would open, the EXT-IO window would appear and attach to the device but as soon as I tried to tune the stick or start receiving various errors would appear and nothing worked... I tried a number of different option settings but still no luck!

Feeling a bit disappointed I put it down while I watched some TV and tried again later. I uninstalled everything and went through the process again but still ended up with the same errors.

I decided to rule out a defective receiver so I uninstalled everything again and installed the manufacturers supplied software.

The drivers and something called BlaseHDTV installed without a hitch. I connected the little supplied antenna to the receiver and set off scanning for TV and radio stations. It didn't complain but found nothing! By now it was well past midnight so I went off to bed in a huff.

This morning I connected the receiver to the roof aerial and it did find TV channels from the two local transmitters Waltham (60% signal strength and 100% quality) and Belmont (low signal strength and quality) but when I tried to watch anything I just got random coloured blocks and random noise. Interestingly it didn't find anything using the DAB or FM radio applications.

So is the receiver defective? Unlikely as it did go away and find TV channels.

The culprit is almost certainly the computer. Being an untrusting soul when it comes to software 'off the internet' I didn't want to try any of this out on my main computers in case it messed anything up. However the laptop is an old Sony Vaio with a Pentium 4-M processor and only 512MB of RAM and can be prone to sluggish behaviour, especially when trashing the hard drive. Saying that it will happily run SDR-Radio with the FUNCube Dongle.

Checking back over the specifications of the receiver it clearly states on the packaging that it requires a USB2.0 port... mmmm the old laptop only has USB1.1! Unfortunately I have grown accustomed to ignoring the pop-up balloon which appears I plug something in...


The looks like the most likely reason for the problems, not enough bandwidth - which would certainly explain the DTV issues. So I will have to try it on another PC...

As Captain Picard would say!  




  




Wednesday, 16 May 2012

Ultra-cheap VHF-UHF Software Defined Radio


Over the last few months various forums and websites I visit have been buzzing with conversations about the RTL-SDR project (e.g Hackaday)

The idea is to take a cheap USB FM/DAB/DTV receiver (for less than £20) that contains a Realtek RTL2832U chipset and an appropriate tuner chip (such as the Elonics E4000) then by using new custom drivers you get yourself a SDR-Radio with a frequency range of around 64 – 1700 MHz

Sound familiar? Yes it is similar to the FUNCube Dongle.

There are a couple of limitations, unlike the FCD the device doesn't have a pre-amplifier so sensitivity might be limited. The IQ sampling is only in 8 bits so the dynamic range will be limited, but because the device doesn't use a USB Soundcard interface like the FCD to pass the IQ samples to the PC the sample rate can be much higher (theoretically 3.2 MS/s) which allows potential decoding of wideband signals which the FCD cannot do.

Over the last few week I have seen a few Youtube videos and read of peoples experiments so my curiosity was piqued and decided to get one to have a go.

There in lies the problem, since news of this hit the internet demand for suitable devices has rocketed and dealers are cashing in and prices have risen and stocks are low. Also as not every USB FM/DAB/DTV receiver has a suitable chipset it is very easy to buy one that won't actually work. There is a list of known working devices here and yesterday while browsing ebay I found a dealer claiming to be selling the Newsky TV28T for around £16 including postage so thought what the hell!

Should be arriving in the next few days so I will keep you posted!

Before I go I should point out that on some forums and discussion groups I visit that some are under the illusion that they are getting a high quality wide band receiver for peanuts and then have complained because they have got a unsupported device or don't understand how the software works. I am under no illusions it will undoubtedly be fiddly, unreliable and inaccurate but it should be FUN! 

If nothing else I will have a way of listening to DAB and watching DTV on my PC, which is hopefully better than my last purchase (which I should really dig out and check what chipset it has!)


  

Tuesday, 15 May 2012

POCSAG and FLEX Decoding with the FCD

With today's modern mobile and wifi networks pagers might seem terribly old fashioned. But pagers are still in use today in places where mobile phones typically cannot reach and also in places where the operation of the radio transmitters contained in mobile phones is problematic or prohibited.

Whilst many of the national networks have closed down some are still going and some locations such as large hospitals have their own systems and are still popular with birdwatchers in Britain and Ireland with companies Rare Bird Alert and Birdnet Information offering news of rare birds sent to pagers that they sell.

Decoding pager messages using a PC involves some software and a receiver usually with a discriminator tap and using the sound card and/or a data-slicer. The most popular software is the PDW suite.

I decided to use the FUNCube Dongle to attempt some decoding as being able to keep everything digital within the PC rather than having audio leads from a scanner plugged into the soundcard meant no problems with audio circuitry messing up the signal. Also the ability to alter the bandwidth should mean I could get some excellent decoding - and I did, both the higher speed and more problematic FLEX and the easier POCSAG protocols.


Thursday, 15 March 2012

Back In The Shack - Reception report VO-52

Things are hopefully get back to some form of normality here after a difficult few weeks.

During my downtime I missed the news that VO-52 HAMSAT had fallen silent on the 28th February a week after my last post. But good news the Dutch built CW/SSB transponder  was reactivated yesterday so last night and this morning I monitored a couple of passes. The transponder was certainly busy and I got some nice captured IQ files to analyse later.

Using just the loft mounted discone I monitored quite a little QSO between G7SVF and I8CVS this morning which I managed to capture using the audio recorder.

VO-52 (15-Mar-2012-0823) by nerdsville

The discone It isn't the best antenna for satellite work, especially with the FUNCube dongle as it's wideband characteristics heavy overload the front end, but it is nice capture all the same, even if it made me slight late this morning and so got caught in the school run traffic.

I did a Google search on the call signs and discovered I8CVS is Domenico Marini from Napoli Italy. Dom appears to be a well known expert in amateur satellite operation.  On that page is a picture of Dom in 2003 next to an impressive antenna array which appears to be sited on top a high rise building (oh the envy!)


While my own set up is much more modest. I have done a little tinkering, building a small UHF Yagi out of some metal coat hangers but have yet to test it in anger. I have also become a little more familiar with my FUNCube setup. I use the SDR-Radio.com application and having updated to a much later beta version have had much more success. There were some issues that involved the swapping the I and Q signal on early versions but these appear to have now been corrected.

After listening to the ICQ Podcast I have been monitoring a few propagation beacons (GB3VHF and GB3BUX) (I will post more on this later) and using those beacons have got the frequency calibration more or less spot on now. I have also discovered that the Doppler Invert option needed setting so now SDR-Radio more or less correct perfectly as the satellites passes (still occasionally needs some manual interaction)

I really must make a real effort to get a licence and become less passive in this hobby, just not sure how I am going to afford an all-modes transceiver mind! 

Monday, 2 January 2012

ARISSat-1 SDR Videos

Just composed a couple of videos showing the use of the FUNCube Dongle Software Defined Radio to decode yesterdays data.

The first shows the FM decode



This video shows the CW/BPSK Telemetry beacon and what appears to be someone using the transponder, both these were using the USB modulation. It also demonstrates the problem of tracking because of the doppler effect.



Note both decodes were preformed on the captured IQ-Wave file.

The videos were created using CAMStudio

Sunday, 1 January 2012

First FCD experiments

I was feeling shattered after a hectic Christmas and being back at work, so it was nice with the New Year break to have a chance to recover. I have spent the weekend around the house and so had a good chance to try out my FUNCube Dongle (FCD) to do some proper satellite reception!

First off I spent a while calibrated my dongle using the excellent user guides available on the yahoo group, and getting to grips with the excellent but somewhat daunting SDR-Radio application. 

I fired up another of my ancient laptops a Sony Vaio, with XP and a pitiful 512MB of RAM. It is a nice machine, with an excellent large display but is a little underpowered. However undeterred with the prospect of some timely satellite passes I installed the necessary software and set off to the summerhouse at the top of the garden with my YAGI and a warm coat.

NOAA Weather Satellites

As I posted about back in October I was hoping if I did get an SDR radio to capture some of the APT images broadcast by the NOAA polar orbiting weather satellites. (Noaa 15, 18 and 19 are currently active)



The SDR-Radio application has the facility to decode the noaa images directly and along with it's built in satellite prediction and doppler correction features it was fairly easy to get some decent images. The huge advantage of the SDR system is being able to alter the bandwidth to accommodate the 34KHz deviation required (as you can see in the image above)


The image above was captured on 31st December at 13:26 GMT from NOAA-19 on 137.100MHz, the left image is the IR, the right being the visible image. If you click to enlarge you can clearly see Spain and the Balearic Islands at the bottom, the UK and most of Northern Europe is covered in dense cloud and is rapidly going into shadow. There is some noise, caused in part by pager transmissions and some course manual doppler correction.


ARISSat-1

As I posted before Christmas this little satellite is still going strong but it's time is very short as reaches the atmosphere. I have been able to receive four afternoon passes in the last two days


As you can see from the image shows, the FCD makes the entire ARISSat-1 2 meter downlink band plan available. The slight slope shows the doppler effect.

On the left you can clearly see the Morse code beacon and the BPSK telemetry segment and the right the FM voice and SSTV transmission. I am really really pleased to have successfully managed to decode some telemetry frames before she meets her fiery death. The decode was done after the passes by processing the recorded IQ wav file. I probably have just one more day to have a chance to try to decode some live telemetry and hopefully forward it via the internet to ARISS.


It goes without saying I have some excellent audio and decoded a couple of SSTV images too.


I love my new toy!


Wednesday, 28 December 2011

FUNcube Dongle - Oh, yes, my precious!


I received a FUNcube Dongle for Christmas but being away from the 'shack' over the holiday and now back in work I have had little time to do anything with it. I did manage a hour of so last night and updated the firmware and had a little scan around the spectrum using SDR-Radio to receive a few signals.

It is certainly a voyage into the unknown, the FCD came in a simple plastic box with a single sheet of A4 which simply told you to go to www.funcubedongle.com but I found the site it a bit of a mess to be honest. Did get some guides from there but most information seems to be on the Yahoo group http://uk.groups.yahoo.com/group/funcube/ 

What became obvious last night was I really miss my dual-monitor set up. There were lots of documents, websites and applications that I had open and navigation was a pain on a single 17" LCD....  must replace the dead screen asap.

Monday, 24 October 2011

NOAA Weather Satellites and SDR

One site I have in my Google Reader list and check regularly is the Hackaday blog


One project they recently featured was Grab your own images from NOAA weather satellites

The main project website describes using a Softrock homebrew SDR(software defined radio) to get the necessary audio file to import into WxImg decoder.

I have been toying with getting hold of the AmSat-UK FunCube SDR dongle, which is now available from Martin Lynch and Sons and using it in a similar way after seeing this article a while back.